Zhide CNC

Status statement
In order to improve the processing of CNC m♠&"©achine tools, after the sp↔☆indle slide oil and cut π ₩ting oil flow into the cenγ® tralized tank, the proces≈∞¥sing will emulsify and deteriorate the oil, and t↓≥™hen the oil emulsification will form a laye≥<&r of oil film, isolating the air<'  and water. In this case, wh≈γδ÷en the machine stops running, the mold i "n the water begins to mulα→↑€tiply, and then produce odor, morα™∏e attached to the oil layer, whenπ¥ running through the suction tank, ε ♥↓the water is sucked into the proc★☆₩essing tank by the beating of the tool to form fλ✘‍₩og to achieve the efficiency of ♠π↓heat loss, but because of this, so the operator↕♦® also follows the inhalation ↑σ↓↕of the same with mold, oil smokδ★e, odor fog. The dirt₩β also sticks to the inside of↕ ₹↔ the machine, in the long run will makeφ >↑ the accuracy of the machine greatly affectedΩε£, the health of the operator is als≥§α‍o lost, in addition, ac £∞™cording to the normal replaceme¶© nt time of the cutting fluid is onc ¶‌$e every three months, if the mach™×εine is not regularlyΩ₩♥∞ replaced, the cutting fluid will b✔∏e too acidic and then corrode the mach∏≈™ine so that it has a failure ↔÷event, or the operator often comes into cont∞↑>♦act with the cutting fluid and when  ↔the cutting fluid mold∑φ€ is too much, Skin contact after a period≈¶§ of time will make the operator's skin rash,✘ ↑✘ even severe skin ulceration.

Product highlights
◆ Greatly improve the ser¥Ωvice life of cutting fluid, reduce costs✘÷ , improve product finish
◆ Eliminate cutting fluid replac€$←ement frequency, waste oil recovery, safety>↕ ε and environmental protection
◆ High strength constant temperature coolin≤↑&♦g to improve tool life
◆ Safe independent complete system, low cost, no ↑✘consumables, maintenance-free, small↑β footprint
◆ The core parts of the imported diaphragm pum±​p make the cutting fluid qδα≈≤uickly and completely separa↔Ω↓te oil and water
◆ Ultra-precision special filter device separa ₽€tion more complete pu✘™ rification
◆ Standard, environmental protection, enerε​♣gy saving and high eff§÷iciency
Water isolation purification oil wa® πter separation removal cβ★€utting constant temperature ≠↔∏₽cooling enhance cutting life Ω→≥reduce tool cost Environ♦♦mental protection improv​$€≠e quality

Improve results
After the actual use, the average three days can ≤ make the cutting fluid of one of our machines • achieve the effect of oil removal, sterilizatiε'®on, deodorization, such results really mεδ‍eet the needs of our company, but also improv£÷e the oil emulsion dete↓₽rioration mold growth, the∑φ← machine is easy to dirty and difficult to ‌↑‌©clean, the discomfort caused by long-term conta≠£☆¶ct, and the cutting fluid does not nee'←d to be replaced (save replacement co∑β₽¥sts) and so on. In the consum≈&able part, the built≠★λ↑-in structure of the♦•π> machine adopts no consumabφ€¥★le design, and the filter core on≈♥ly needs to be cleaned regularly. Thi↑↑&™s design also saves a sum∏‍™ of consumable costs for our"≠ company.

Higher stability
◆ Compressed air drive, ✘π∞ no motor, reducer and other additi✘©♦₩onal electric configuration, no mecha≈"nical seal, maximize the red​§↑★uction of leakage and unexplained shut←≥★down, to ensure the stability and continuity of λΩεproduction.
◆ Air valve design with ↔γpatented technology, no lubrication, zero'® dead point. High adapta©×bility to all types of co♠λ♦λmpressed air, providing reliable and worry-f±↔ree operation.
◆ Self-priming, maximum su‍​↓∑ction range (wet) up to 9.2   meters, suitable for<φ€ a variety of installation condition•>≈s, can replace some submersible pump.
◆ Can run dry for a long time, and ₽σthere will be no temperature rise and damage to ↑♦the components. Avoid✘≠♠ safety hazards and production ri±δsks.

Greater versatility
◆ Each wet part of the f ™​☆luid section has a variety of materials to choos ¶™e from, which is suitable for d∑αifferent industries and different mat±↕₽←erials. Whether it is wε¶ear type media, corrosive media, or high/low tem₹‍perature media, there arδ≠←≥e special pumps to match it.
◆ Multi-interface customized design, convenien∑<t for OEM customers to useδ✘$≈ in different installation Spδ≠∑aces and piping systems.
◆ Wide flow range, can provide 1/4 inch to‌< 3 inch different size pump, fluid cove♣$Ωrage of 1lpm~800Ipm.

Easier maintenance
◆ Modular structure design,★∑> reduce the number of∑✔↓  parts, reduce maintenance time and co$×↔st, maximize the life cycle cost of equ↑λ∑∏ipment.
◆ Fewer wearing parts, no rota≈&ting parts in the equipment, redu •↓ce the wear rate and the number of wo↑♠∏γrn parts.
◆ Small size, light weight, no additional♦ש♠ maintenance space and maintenance perso¥♦‍↔nnel.
◆ Humanized design, maintenance without special≤↓₹ tools or lifting tools.